Products

TeraFlex JL / JT: HD Ball Joints are engineered to handle the increased load caused by oversized tires and offset wheels. Fits all JL Wrangler/Unlimited and JT Gladiator models with Dana 30 or Dana 44 front axles

• Threaded ball stud retaining ring designed for precise preload adjustment during assembly and future adjustments

• 30mm (1.18”) adjustable ball stud for accurate initial and future preload adjustments using simple hand tools — innovative feature ensures a long-life w/ flawless and predictable operation

• 2 grease zerk fittings are accessible from either side w/ axle shafts installed, including larger RCV shafts

• Dual helical grease grooves machined in the ball stud allow spent grease to exit through the low-profile seal

• Heat-treated 4140 chromoly ball studs

• Heat-treated 1045 carbon steel housing and threaded retaining ring

• Magnesium Phosphate coating provides corrosion resistance and decreases friction

• Hard alloy tool steel slotted wear plate for ball stud to socket wear protection

• Magnesium phosphate coating provides corrosion resistance and decreases friction

• Includes factory style slotted nuts and cotter pins

• Low profile single lip dust seal prevents contaminants compared to easily torn conventional dust boots

• Heavy-duty snap ring on upper ball joint prevents ball joint separation from the axle during extreme off-roading

• Ball joint preload adjustability provides the end user w/ near effortless wear adjustment

• Preload adjustment requires simple tools and can be performed with the vehicle on the ground

• 1 large set screw on each ball joint

• Large 8-sided adjuster handles more torque

Local Pickup or Install Only - Contact us for Availability 

The rear axle experiences tremendous amounts of lateral force while driving and those effects increase exponentially during off-road driving. The TeraFlex JL: Rear HD Forged Adjustable Track Bar withstands these abusive side loads to dramatically improve handling. Track Bars also allow lateral adjustment of the axle for proper axle alignment as well as cycling through full suspension travel without interfering with other components. Our rear track bar also maximizes exhaust and differential cover clearances. Our Rear HD Forged Adjustable Track Bar is recommended for 2.5–6” lifts. Bolts into factory locations or our Rear Lower Track Bar Bracket (2.5–4.5” Lift: # 1953600) — no cutting or welding required. This is the same Rear Track Bar used in our 2.5–4.5” Alpine RT Suspension Systems. A must for anyone who takes their rig off road!

• 50% stronger than factory rear track bar

• Bolts into factory locations or our Rear Lower Track Bar Bracket (2.5–4.5” Lift: # 1953600) — no cutting or welding required

• Adjustable end features an improved turn-buckle design w/ built-in clamp and alignment feature for a hassle-free install and length adjustment

• Adjustable from 0.5” shorter than stock to 1” longer than stock

• High-quality, maintenance-free factory-style bushings w/ an additional rate plate for superior handling and responsive control

• OEM-style rubber boots maximize longevity and aid in smooth, quiet operation

• Unique backbone/reinforced rib for additional strength and rigidity

• Clears Tera CRD60 rear differential cover

Local Pickup or Install Only - Contact us for Availability 

The front axle experiences tremendous amounts of lateral force while turning and those effects increase exponentially during off-road driving. The TeraFlex JL / JT: Front HD Forged Adjustable Track Bar withstands these abusive side loads to dramatically improve steering response and handling. Track Bars also allow lateral adjustment of the axle for proper axle alignment as well as cycling through full suspension travel without interfering with other components. Our Front HD Forged Adjustable Track Bar is recommended for 2.5–6” lifts. Bolts into factory locations or our Front Lower Track Bar Bracket (2.5–3.5” Lift: # 1953250 or 4.5” Lift: # 1953500) — no cutting or welding required. This is the same Front Track Bar used in our 2.5–4.5” Alpine RT and Alpine CT Suspension Systems. A must for anyone who takes their rig off road!

• Bolts into factory locations or our Front Lower Track Bar Brackets (2.5–3.5” Lift: # 1953250 or 4.5” Lift: 1953500) — no cutting or welding required

• Adjustable end features an improved turn-buckle design w/ built-in clamp and alignment feature for a hassle-free install and length adjustment

• Adjustable from 0.5” shorter than stock to 1” longer than stock

• High-quality, maintenance-free factory-style bushings w/ an additional rate plate for superior handling and responsive control

• OEM-style rubber boots maximize longevity and aid in smooth, quiet operation

• Unique backbone/reinforced rib for additional strength and rigidity

Local Pickup or Install Only - Contact us for Availability 

The TeraFlex JL / JT: HD Forged Drag Link Kit and HD Chromoly Tie Rod Kit withstand extreme conditions and abuse that typically causes factory steering components to bend and fail on stock and lifted JL Wrangler/Unlimited and JT Gladiator models. The vague and unpredictable OEM steering leaves much to be desired. Our HD Forged Drag Link Kit and HD Chromoly Tie Rod Kit beef up the steering on all JL and JT models, including stock and lifted vehicles. A must for anyone who takes their rig off road!

HD Forged Drag Link Kit:

• Solid 1.5” O.D. I-beam inspired fully Forged Drag Link eliminates excess movement during hard steering maneuvers

• 100% stiffer than factory drag link to help eliminate front end shimmy and other alignment issues

• Uses OEM style turn buckle adjuster for simple alignment adjustments

• Drag Link features a premium black e-dipped coating that provides superior durability and corrosion resistance

• Compatible w/ all OEM tie rods HD Chromoly Tie Rod Kit:

• HD 1-5/8” O.D. x 0.275” wall 4140 heat treated chromoly steel

• More than 66% stronger and 75% stiffer than factory tie rod

• Adjustable length from 59–61”

• Same forged threaded ends as JK Wrangler/Unlimited

• Tie Rod is UV protected triple-stage powder coat for corrosion resistance

• Relocates steering stabilizer above tie rod to help reduce damage to the stabilizer shaft or body Both:

• One tie rod end joint rotation is limited to 2 degrees of freedom to eliminate wobble and noise, while the other joint has full motion to allow for full turning

• Tie Rod Joints incorporate same features found in TeraFlex Ball Joints, including 4140 chromoly ball/stud and 1045 carbon steel housing

• Adjustable rod end preload tension ensures long-term durability — adjustable on vehicle

• Joint is pressed into rod end housing and secured w/ snap ring

• Features greaseable joints coated w/ magnesium phosphate

• Tie Rod end forgings feature a premium black e-dipped coating that provides superior durability and corrosion resistance

• Compatible w/ all TeraFlex components including Front HD Forged Adjustable Track Bar, Delta Brake System, Front Sway Bar Quick Disconnects, Tera60 HD Front Axle w/ 3.5” O.D. Axle Housing Tubes, HD Differential Covers, Off-Road Wheels, and Falcon Steering Stabilizers

• Compatible w/ OEM knuckle and 17”+ wheels

• Installation does not require any cutting or removal of factory bracketry

Local Pickup or Install Only - Contact us for Availability 

The 2.5" Alpine CT2 Short Arm Suspension System was designed for the enthusiast who wants to fine tune their suspension. Alpine Short Control Arms allow tuning of the caster and pinon angles centering of the axles in the wheel wells and wheelbase adjustment. The zero-maintenance adjustable control arms make the Alpine CT2 the perfect all-around suspension system. Adjustable Alpine Short Control Arms balance front caster and pinion angles as well as optimize rear pinion angles anti-squat geometry and tire position on vehicles with 0-4.5" lifts. The Front HD Forged Adjustable Track Bar improves steering response centers the axle to optimize vehicle roll center and reduces body roll for unsurpassed handling. This results in improved suspension geometry and relaxed control arm angles for a superior ride quality and performance regardless of terrain. These systems restore front and rear roll axis angles to minimize brake dive and acceleration squat. TeraFlex suspension systems provide reduced noise vibration and harshness (NVH). Alpine CT Suspension Systems are engineered for hardcore Jeeping without sacrificing weekday ride comfort! Does NOT include shocks. We recommend Falcon Performance Shocks. Falcon shock absorbers and TeraFlex lift coil springs have been engineered together to improve both compression and rebound for optimal vehicle stability. Falcon shocks and steering stabilizers sold separately.

• Lift Height: 2.5"

• Sport/Overland Fenders: 35" Tires

• Rubicon Fenders: 35" Tires CT Short Arm Suspension Systems:

• Adjustable Alpine Short Control Arms balance front caster angle and pinion angles as well as optimize rear pinion angle and tune anti-squat geometry for proper suspension alignment on 0-4.5" lift kits

• Alpine Short Control Arms are constructed from durable 42mm x 4mm wall DOM tube for maximum strength

• Bolts to the factory control arm mounting brackets

• Install and drive simple bolt-on installation – no welding required Cross-Trail:

• Delivers true Cross-Trail (CT) performance

• Dependable performance w/ zero worries

• Positive, responsive handling w/ reduced NVH

• High-quality, dependable, maintenance-free, factory-style bushings provide excellent NVH damping and ride quality.

• Front HD Forged Adjustable Track Bar improves steering response, centers axle to optimize vehicle roll center, and reduces body roll for unsurpassed handling

• Front and Rear Progressive Bump Stops provide progressive compression during high-speed suspension movement

• Features Front Sway Bar Quick Disconnects

• Full range of movement for off-road flex and articulation

• Install and drive, simple bolt-on installation – no welding required

• TeraFlex Limited Lifetime Warranty against defects

Local Pickup or Install Only - Contact us for Availability 

A 3.5” suspension system opens up a new world of tire sizes and off-road possibilities. If you have that “do it all” attitude, one of our 3.5” Alpine CT3 Extended-Travel Suspension Systems will make it happen. The Alpine CT3 Long Arm features our Alpine Long Arms & Brackets as well as a Front HD Forged Adjustable Track Bar and Front and Rear Track Bar Brackets for maximum tunability and flawless performance for years to come. Adjustable Alpine Long Arms balance front caster angle and pinion angles as well as optimize rear pinion angles, anti-squat geometry, and tire position on vehicles with 3–6” lifts. On higher lifts, Long Arm Brackets reposition frame-end control arm mounting points to restore near factory orientation to reduce bushing stress during extreme droop as well as shock load transferred through the Long Control Arms. The Front HD Forged Adjustable Track Bar and Track Bar Brackets improve steering response, center the axles to optimize vehicle roll center, and reduce body roll for unsurpassed handling. Extended-Travel Suspension Systems include carefully selected components to safely provide 16” of rear suspension travel. This results in improved suspension geometry and relaxed control arm angles for a superior ride quality and performance regardless of terrain. These systems restore front and rear roll axis angles to minimize brake dive and acceleration squat. TeraFlex suspension systems provide reduced noise, vibration, and harshness (NVH). Alpine CT Suspension Systems are engineered for hardcore Jeeping without sacrificing weekday ride comfort! Does NOT include shocks. We recommend Falcon Performance Shocks. Falcon shock absorbers and steering stabilizers available separately.

• Lift Height: 3.5”

• Sport/Overland Fenders: 33–35” Tires

• Rubicon/Mojave Fenders: 35–37” Tires CT Long Arm Extended-Travel:

• Adjustable Alpine Long Arms & Brackets balance front caster angle and pinion angles as well as optimize rear pinion angles and tune anti-squat geometry for proper suspension alignment on 3–6” lift kits

• Constructed from durable 42mm x 4mm or 50mm x 5mm wall DOM tube for maximum strength

• On higher lifts, bolt-on Long Arm Brackets reposition frame-end control arm mounting points to restore near factory orientation to reduce bushing stress during extreme droop as well as shock load transferred through the Long Control Arms

• Brackets are gusseted and reinforced for superior strength w/ reduced NVH

• Brackets feature a triple-stage powder coating that provides superior durability and corrosion resistance

• Long Arm Suspension Crossmember provides additional strength

• Driveshaft Lowering Spacers, Forged ST Sway Bar, and Extended-Travel Accessory Kit safely provide 16” of rear suspension travel

• Rear Coil Spring Retainers prevent the springs from unseating during full suspension travel Cross-Trail:

• Delivers true Cross-Trail (CT) performance

• Dependable performance w/ zero worries

• Positive, responsive handling w/ reduced NVH

• High-quality, dependable, maintenance-free, factory-style bushings provide excellent NVH damping and ride quality

• Front HD Forged Adjustable Track Bar and Track Bar Brackets improves steering response, centers axle to optimize vehicle roll center, and reduces body roll for unsurpassed handling

• Front and Rear Progressive Bump Stops provide progressive compression during high-speed suspension movement

• Features Front Sway Bar Quick Disconnects

• Full range of movement for off-road flex and articulation

Local Pickup or Install Only - Contact us for Availability 

TeraFlex Alpine CT (Cross-Trail) Suspension Systems build on our Sport ST (Street & Trail) Suspension Systems. A 3.5” suspension system opens up a new world of tire sizes and off-road possibilities. If you have that “do it all” attitude, the 3.5” Alpine CT3 Short Arm Extended-Travel Suspension System will make it happen. Our Alpine Short Control Arms, Front HD Forged Adjustable Track Bar, and Front and Rear Track Bar Axle Brackets combined with our extended-travel components provide maximum tunability and flawless performance for years to come. Adjustable Alpine Short Control Arms balance front caster angle and pinion angles as well as optimize rear pinion angles, anti-squat geometry, and tire position on vehicles with 0–4.5” lifts. The Front HD Forged Adjustable Track Bar and Front and Rear Track Bar Axle Brackets improve steering response, centers the axle to optimize vehicle roll center, and reduces body roll for unsurpassed handling. Extended-Travel Suspension Systems include carefully selected extended-travel components to safely provide 16” of rear suspension travel. This results in improved suspension geometry and relaxed control arm angles for a superior ride quality and performance regardless of terrain. These systems restore front and rear roll axis angles to minimize brake dive and acceleration squat. TeraFlex suspension systems provide reduced noise, vibration, and harshness (NVH). Alpine CT Suspension Systems are engineered for hardcore Jeeping without sacrificing weekday ride comfort! Does NOT include shocks. We recommend Falcon Performance Shocks. Falcon shock absorbers and TeraFlex lift coil springs have been engineered together to improve both compression and rebound for optimal vehicle stability. Falcon shock absorbers and steering stabilizers available separately.

• Lift Height: 3.5”

• Sport/Overland Fenders: 35” Tires

• Rubicon Fenders: 37” Tires

• Adds Front and Rear Track Bar Axle Brackets CT Short Arm Extended-Travel:

• Adjustable Alpine Short Control Arms balance front caster angle and pinion angles as well as optimize rear pinion angle and tune anti-squat geometry for proper suspension alignment on 0–4.5” lift kits

• Constructed from durable 42mm x 4mm wall DOM tube for maximum strength

• Bolts to the factory control arm mounting brackets

• Extended-Travel Axle Brackets, Driveline Lowering Spacers, Forged ST Sway Bar, and Extended-Travel Shock Accessory Kit safely provide 16” of rear suspension travel

• Bolt-on Extended-Travel Axle Brackets install between factory axle mounts and rear upper control arms

• Rear Coil Spring Retainers prevent the springs from unseating during full suspension travel Cross-Trail:

• Delivers true Cross-Trail (CT) performance

• Dependable performance w/ zero worries

• Positive, responsive handling w/ reduced NVH

• High-quality, dependable, maintenance-free, factory-style bushings provide excellent NVH damping and ride quality

• Front HD Forged Adjustable Track Bar improves steering response, centers axle to optimize vehicle roll center, and reduces body roll for unsurpassed handling

• Front and Rear Progressive Bump Stops provide progressive compression during high-speed suspension movement

• Features Front Sway Bar Quick Disconnects

• Full range of movement for off-road flex and articulation

• TeraFlex Limited Lifetime Warranty against defects

Local Pickup or Install Only - Contact us for Availability 

The 4.5” Alpine CT4 Long Arm Extended-Travel Suspension System is engineered for the enthusiast who demands an off-road capable suspension with maximum adjustability, flex, durability, and quiet performance. This all-inclusive system includes everything from our industry leading adjustable Alpine Long Arms & Brackets to our exclusive rear Extended-Travel System. The Alpine CT4 is designed to flex and droop over boulders and fly across flats like nothing you have ever experienced. And like all TeraFlex lifts, the highway manners of the CT4 are legendary. Adjustable Alpine Long Arms balance front caster angle and pinion angles as well as optimize rear pinion angles, anti-squat geometry, and tire position on vehicles with 3–6” lifts. On higher lifts, Long Arm Brackets reposition frame-end control arm mounting points to restore near factory orientation to reduce bushing stress during extreme droop as well as shock load transferred through the Long Control Arms. The Front HD Forged Adjustable Track Bar and Track Bar Brackets improve steering response, center the axles to optimize vehicle roll center, and reduce body roll for unsurpassed handling. Extended-Travel Suspension Systems include carefully selected components to safely provide 16” of rear suspension travel. This results in improved suspension geometry and relaxed control arm angles for a superior ride quality and performance regardless of terrain. These systems restore front and rear roll axis angles to minimize brake dive and acceleration squat. TeraFlex suspension systems provide reduced noise, vibration, and harshness (NVH). Alpine CT Suspension Systems are engineered for hardcore Jeeping without sacrificing weekday ride comfort! Does NOT include shocks. We recommend Falcon Performance Shocks. Falcon shock absorbers and steering stabilizers available separately.

Lift Height: 4.5”

• Sport/Overland Fenders: 33–37” Tires

• Rubicon/Mojave Fenders: 35–39” Tires

• Aftermarket Fenders: 39”+ Tires CT Long Arm Extended-Travel:

• Adjustable Alpine Long Arms & Brackets balance front caster angle and pinion angles as well as optimize rear pinion angles and tune anti-squat geometry for proper suspension alignment on 3–6” lift kits

• Constructed from durable 42mm x 4mm or 50mm x 5mm wall DOM tube for maximum strength

• On higher lifts, bolt-on Long Arm Brackets reposition frame-end control arm mounting points to restore near factory orientation to reduce bushing stress during extreme droop as well as shock load transferred through the Long Control Arms

• Brackets are gusseted and reinforced for superior strength w/ reduced NVH

• Brackets feature a triple-stage powder coating that provides superior durability and corrosion resistance

• Long Arm Suspension Crossmember provides additional strength

• Driveshaft Lowering Spacers, Forged ST Sway Bar, and Extended-Travel Accessory Kit safely provide 16” of rear suspension travel

• Rear Coil Spring Retainers prevent the springs from unseating during full suspension travel Cross-Trail:

• Delivers true Cross-Trail (CT) performance

• Dependable performance w/ zero worries

• Positive, responsive handling w/ reduced NVH

• High-quality, dependable, maintenance-free, factory-style bushings provide excellent NVH damping and ride quality

• Front HD Forged Adjustable Track Bar and Track Bar Brackets improves steering response, centers axle to optimize vehicle roll center, and reduces body roll for unsurpassed handling

• Front and Rear Progressive Bump Stops provide progressive compression during high-speed suspension movement

• Features Front Sway Bar Quick Disconnects

• Full range of movement for off-road flex and articulation

• TeraFlex Limited Lifetime Warranty against defects

Local Pickup or Install Only - Contact us for Availability

The rear axle experiences tremendous amounts of lateral force while driving and those effects increase exponentially during off-road driving. The TeraFlex JT: Rear HD Forged Adjustable Track Bar withstands these abusive side loads to dramatically improve handling. Track Bars also allow lateral adjustment of the axle for proper axle alignment as well as cycling through full suspension travel without interfering with other components. Our rear track bar also maximizes exhaust and differential cover clearances. Our Rear HD Forged Adjustable Track Bar is recommended for 2.5–6” lifts. Bolts into factory locations or our Rear Lower Track Bar Bracket (0–6.5” Lift: # 1963600) — no cutting or welding required. This is the same Rear Track Bar used in our 2.5–4.5” Alpine RT Suspension Systems. A must for anyone who takes their rig off road!

• 50% stronger than factory rear track bar

• Bolts into factory locations or a Rear Axle Track Bar Bracket (0–6.5” Lift: # 1963600) — no cutting or welding required

• Adjustable end features an improved turn-buckle design w/ built-in clamp and alignment feature for a hassle-free install and length adjustment

• Adjustable from 0.5” shorter than stock to 1” longer than stock

• High-quality, maintenance-free factory-style bushings w/ an additional rate plate for superior handling and responsive control

• OEM-style rubber boots maximize longevity and aid in smooth, quiet operation

• Unique backbone/reinforced rib for additional strength and rigidity

• Clears Tera CRD60 rear differential cover

Local Pickup or Install Only - Contact us for Availability 

Are you running 37 in. or larger tires on your JK? If you answered yes, we feel the RockJock Currectlync Modular Extreme Steering System is a mandatory upgrade for those who get their rigs out in the rocks! Being pro-active, so you don't get stranded in the wilderness with bent or broken factory steering components is the smart thing to do for your family's safety.
RockJock's completely bolt-on Modular Extreme Steering System is commonly referred to as our 2 1/2 Ton system. Features include massive a 1 5/8 in. diameter drag link tube and 1 5/8 in. diameter 4130 chromoly heat treated tie rod tube, 1 1/4 in. RH/LH thread forged steel rod ends, removable rod end cartridges that may be used in standard or reversed orientation, premium jam nuts and our heavy duty steering stabilizer shock bracket kit. Components are powder coated semi-gloss black so they are ready for install right out of the box!
Our heavy duty U-bolt style steering stabilizer shock mounting bracket kit is included to allow you to easily reinstall your factory stabilizer shock or an upgraded CE-9170SD1 Rancho RS5000 stabilizer shock.
More commonly in applications that require this heavy of a steering system, you’ll be looking to install Ram Assist steering. We offer easy to install ram mounting brackets for this tie rod here.
The removable cartridges in the rod ends offer many advantages.

• They are able to be replaced independently of the forged rod end, saving cost
• A spare can easily be carried in the vehicle for trail repairs (carry our JK-9703W wrench with you as well!)
• If a cartridge end is removed and replaced, the vehicle does not have to be realigned, because the tie rod /drag link length adjustment was not compromised
• If a high-steer configuration is desired, cartridges may be easily removed from the rod end forgings and reinserted from the top and simply tightened back down

This easy to install kit is completely bolt-on and requires no modifications or machining to any part of the vehicle!

Kit Fits:

• JK Wrangler Unlimited (4-door) - All Models (with stock Dana 30 or 44 front differential)
• JK Wrangler (2-door) - All Models (with stock Dana 30 or 44 front differential)

Kit Includes:

• (1) Tie Rod Assembly
• (1) Drag Link Assembly
• (1) Steering Stabilizer Shock Bracket Kit

Fitment Specs.:

• Intended for use with 0–6 in. of lift out of the box
• For use on any factory JK Dana 30 and Dana 44 differentials
• Can be used on aftermarket Dana 44 differentials that retain the factory outer steering knuckles, or aftermarket knuckles that retain the stock JK taper in the rod end mounting holes
• All 4 rod end tapers are designed to fit the vehicle's stock, original taper for ease of installation. If your tapers have been enlarged or drilled out – this will no longer be a bolt-on kit.
• If your tapers have been drilled out, or if you would like to attempt to use these components on an other than stock differential, you may review our additional cartridge offerings here.

Component Specs.:

• Tie Rod = 1 5/8 in. dia. 4130 heat treated chromoly tube
• Tie Rod End Forgings = 1 1/4 in.-12 RH/LH threads, forged steel
• Drag Link = 1 5/8 in. dia. DOM steel tube
• Drag Link End Forgings = 1 1/4 in.-12 RH/LH threads, forged steel
• Rod End Cartridges = JK Taper stock taper on the pin, 1 3/4 in.-12 threads on the O.D. and 9/16 in.-18 threads on the pin
• Steering Stabilizer Shock Bracket Plate = 1/4 in. laser cut and formed steel
• Steering Stabilizer Shock Bracket U-Bolts = 3/8 in.-24 thread

Notes:

• Wrench flats on the tubes require a 1 1/2 in. wrench, jam nuts require a 1 7/8 in. wrench
• Rod end cartridges require our JK-9703W wrench or a 2 in. wrench or impact socket
• If you decide to flip the Rod End Cartridges to mount the components in a high-steer configuration, keep in mind that all of the corresponding tapered holes must be retapered from the other direction as well
• Intended for use with 0–6 in. of lift out of the box
• Do not use this unit outboard of the lift amount requirements outlined above! Deviating from these parameters will cause damage and premature wear to the components!
• You must grease all rod ends via their zerk fittings before use
• Grease unit with non-synthetic, hi-moly lube grease, such as our CE-9013G
• The Steering Stabilizer Bracket Kit that is included may be used with the stock stabilizer shock, an upgraded CE-9170SD1 Rancho RS5000 stabilizer shock and likely many other aftermarket shocks
• We offer easy to install Ram Assist brackets for this tie rod here.

Instruction Manual:

• JK-9703 Kit

Parts List:

• Complete Tie Rod Assembly:  JK-9703TR
• Tie Rod Tube (only):  JK-9703TRS
• Tie Rod End Forging (LH thread):  JK-9703TRFL
• Tie Rod End Forging (RH thread):  JK-9703TRFR
• Complete Drag Link Assembly:  JK-9703DL
• Drag Link Tube (only):  JK-9703DLS
• Drag Link End Forging (LH thread):  JK-9703DLFL
• Drag Link End Forging (RH thread):  JK-9703DLFR
• Rod End Cartridge (fits all 4 points):  JK-9703C
• 1 1/4 in.-12 LH Jam Nut:  CE-9114LJN
• 1 1/4 in.-12 RH Jam Nut:  CE-9114JN
• Tie Rod End Boot:  JK-9703TRB
• Drag Link End Boot:  JK-9703DLB
• Cotter Pin (fits all 4 points):  CE-98338A190
• Steering Stabilizer Shock Bracket Kit:  JK-9703SB
• Cartridge Wrench:  JK-9703W

Local Pickup or Install Only - Contact us for Availability 

Have you seen the size of your JK’s stock steering? Being pro-active, so you don't get stranded in the wilderness with bent or broken factory steering components, is the smart thing to do for your family's safety. RockJock's Currectlync Steering System for your JK Wrangler or Unlimited is must-have for those who get their vehicles out in the dirt!
RockJock's completely bolt-on Currectlync Steering System features an alloy steel 42mm (1.65 in.) diameter tie rod, a solid forged steel, organically shaped, high articulation drag link, larger forged, greasable rod ends, premium jam nuts and adjusters and it's painted black, so it's ready for install right out of the box!
The new drag link’s organic shape ensures maximum up travel where your steering components are concerned. With this piece installed, you should also consider our RJ-9120FJKF organically shaped forged Trac Bar and our RJ-107101-101 adjustable front bump stop kit so that you can fine tune your vehicle to truly achieve maximum up travel out of your build.
Our heavy duty U-bolt style steering stabilizer shock mounting bracket kit is included to allow you to easily reinstall your factory stabilizer shock or an upgraded CE-9170SD1 Rancho RS5000 stabilizer shock.
Both the tie rod and drag link feature double adjusters so that they do not require removal from the vehicle for adjustment once installed. This unit is designed for use on stock height or lifted vehicles, but for those with big tires, these components are also compatible with ram assist steering (see ram assist mounting bracket options here.
This easy to install kit requires no modifications or machining to any part of the vehicle!

Kit Fits:

• JK Wrangler Unlimited (4-door) - All Models (with stock front differential)
• JK Wrangler (2-door) - All Models (with stock front differential)

Kit Includes:

• 45mm (1.65 in.) Alloy Steel Tie Rod Assembly (w/ Ends)
• Forged, Organically Shaped Drag Link Assembly (w/ Ends)
• Steering Stabilizer Shock Bracket Kit
• All required hardware and step-by-step instructions

Kit Features:

• Heavy duty greasable rod ends for increased strength and long service life
• Double adjusters on both rods simplifies alignment (eliminates the need to remove rod ends, stabilizer shock or ram components to adjust tie rod)
• Compatible with ram assist steering (see our ram assist mounting solutions here)
• 2-year warranty

Fitment Specs.:

• Designed for stock height or up to 6 in. lifted vehicles
• Compatible with any OEM JK wheel
• Works with any size tire
• For use on any factory JK Dana 30 and Dana 44 differentials
• Can be used on aftermarket Dana 44 differentials that retain the factory outer steering knuckles, or aftermarket knuckles that retain the stock JK taper in the rod end mounting holes
• All 4 rod end tapers are designed to fit the vehicles stock, original taper for ease of installation. If your tapers have been enlarged or drilled out – this will no longer be a bolt-on kit

Notes:

• Do not use this unit outboard of the lift amount requirements outlined above! Deviating from these parameters will cause damage and premature wear to the components!
• In vehicles with no lift, or smaller lifts, the tips of the drag link ends may require slight trimming to prevent them from touching each other inside the adjuster sleeve
• In stock knuckle applications, no increase in bump stop is required for the sake of the Drag Link.
• In High Steer Knuckle applications, to squeeze the absolute most up travel out of your vehicle, we recommend the use of our RJ-9120FJKF organically shaped forged Trac Bar and our RJ-107101-101 Adjustable Bump Stop Kit.
• The Steering Stabilizer Bracket Kit that is included allows the stock stabilizer shock to be reused.
• If you are intending to use a Bilstein 5100 series stabilizer shock with this system, see Bilstein part number 24-158428 for the bolt-on shock.
• If you are intending to use a Bilstein 5100 series stabilizer shock with this system and our High Steer Knuckle Kit, see Bilstein part number 33-292984 for the bolt-on shock.
• If you are intending to use a Fox stabilizer shock with this system, see Fox part number 985-24-145 is the shock for this application, but it is not a simple bolt on affair in all instances. Some grinding and fitment may need to be done for optimum clearance and performance.
• If you are intending to use a Fox ATS stabilizer shock with this system, see Fox part number 803-02-039 for the proper mounting solution.
• If you are intending to use a Rancho RS5000 stabilizer shock with this system, see our part number CE-9170SD1 for the bolt-on shock.
• If you’ll be using this Tie Rod with ram assist, check out our easy to install ram mounting brackets for this tie rod here.
• You must grease all rod ends via their zerk fittings before use. Grease unit with non-synthetic, hi-moly lube grease, such as our CE-9013G.

Instruction Manual:

• JK-9704 Kit

Product Video:

• JK-9704 Kit

Component Specs.:

• Tie Rod = 42mm (1.654 in.) dia. alloy steel tube with indexed ends for maximum strength
• Tie Rod Ends = 1 1/8 in.-18 RH threads (on both), forged steel
• Drag Link = Organically shaped, solid forged steel
• Drag Link Ends = 1 1/8 in.-18 RH/LH threads, forged steel
• Drag Link Adjuster Sleeve = 5.080 in. Long x 1 1/8 in.-18 RH/LH threads, forged steel
• Steering Stabilizer Shock Bracket Plate = 1/4 in. laser cut steel
• Steering Stabilizer Shock Bracket U-Bolts = 3/8 in.-24 thread

Parts List:

• Tie Rod Assembly (complete):  JK-9704TR
• Drag Link Assembly (complete):  JK-9704DL-T
• Steering Stabilizer Shock Bracket Kit:  JK-9703SB
• Tie Rod End (driver’s side):  JK-9704TR-1
• Tie Rod Tube (only):  JK-9704TR-3
• Tie Rod End (passenger’s side):  JK-9704TR-2
• Tie Rod Double Adjuster:  JK-9704TR-4
• Tie Rod Adjuster Clamp:  JK-9704TR-5
• Tie Rod Jam Nut (fits both points):  JK-9704TR-6
• Drag Link End (at Pitman Arm):  JK-9704DL-1
• Drag Link Threaded Adjuster:  JK-9704DL-3
• Drag Link End (long, at knuckle):  JK-9704DL-2T
• Drag Link Adjuster Clamp:  CE-9704DL-4
• Rod End Boot (fits all 4 points):  JK-9703DLB
• Rod End Nut (fits all 4 points):  JK-9704NUT
• Rod End Cotter Pin (fits all 4 points):  CE-98338A190
• Rod End Zerk Fitting (fits all 4 points):  CE-1103K21

Local Pickup or Install Only - Contact us for Availability 

TeraFlex Alpine CT (Cross-Trail) Suspension Systems build on our Sport ST (Street & Trail) Suspension Systems. The TeraFlex 3" Alpine CT3 Outback Overland Short Arm Suspension System is built to handle expedition-style overland travel such as the Canning Stock Route in Australia the Silk Road in China or your favorite trail in the U.S. The Alpine CT3 Outback Overland builds on the standard 3" Alpine CT3 by adding custom load-enhanced heavy-duty rate coil springs. These upgraded springs maintain the lift height when loaded with heavy gear. The Outback Overland Suspension System is built to handle the toughest trails! Our adjustable Alpine Short Control Arms balance front caster angle and pinion angles as well as optimize rear pinion angles anti-squat geometry and tire position on vehicles with 2-4" lifts. The HD Forged Adjustable Front and Rear (4"+) Track Bars and Rear Track Bar Bracket improve steering response center the axles to optimize vehicle roll center and reduce body roll for unsurpassed handling. This results in improved suspension geometry and relaxed control arm angles for a superior ride quality and performance regardless of terrain. These systems restore front and rear roll axis angles to minimize brake dive and acceleration squat. TeraFlex suspension systems provide reduced noise vibration and harshness (NVH). Alpine CT Suspension Systems are engineered for hardcore Jeeping without sacrificing weekday ride comfort! Does NOT include shocks. We recommend Falcon Performance Shocks. Falcon shock absorbers and TeraFlex lift coil springs have been engineered together to improve both compression and rebound for optimal vehicle stability. Alpine CT3 Outback Overland Suspension Systems are offered without shock absorbers. 

Alpine CT3 Outback Overland:

• Lift Height: 3"

• Max Tire Diameter: 35"

• Designed for the additional cargo demands of overland driving

• Load-enhanced heavy-duty rate coil springs CT Short Arm Suspension Systems:

• Adjustable Alpine Short Control Arms balance front caster angle and pinion angles as well as optimize rear pinion angle and tune anti-squat geometry for proper suspension alignment on 2-4" lift kits

• Alpine Short Control Arms are constructed from durable 42mm x 4mm wall DOM tube for maximum strength

• Bolts to the factory control arm mounting brackets

• Install and drive simple bolt-on installation – no welding required Cross-Trail:

• Delivers true Cross-Trail (CT) performance

• Dependable performance w/ zero worries

• Positive, responsive handling w/ reduced NVH

• High-quality, dependable, maintenance-free, factory-style bushings provide excellent NVH damping and ride quality.

• HD Forged Adjustable Front and Rear (4"+) Track Bars and Rear Track Bar Bracket improve steering response, center axles to optimize vehicle roll center, and reduce body roll for unsurpassed handling

• Front SpeedBump and rear Progressive Bump Stops provide progressive compression during high-speed suspension movement

• Coil spring retainers prevent the springs from unseating during full suspension travel

• Full range of movement for off-road flex and articulation

• TeraFlex Limited Lifetime Warranty against defects

Local Pickup or Install Only - Contact us for Availability 

TeraFlex Alpine CT (Cross-Trail) Suspension Systems build on our Sport ST (Street & Trail) Suspension Systems. The TeraFlex 4" Alpine CT4 Long Arm Suspension System is developed for the off-roader craving trails and rocks as well as highway control in a no-compromise package. The Alpine CT4 features our adjustable Alpine Long Control Arms & Brackets as well as HD Adjustable Front and Rear Track Bars for full suspension adjustability no matter the terrain! Our adjustable Alpine Long Control Arms balance front caster angle and pinion angles as well as optimize rear pinion angles anti-squat geometry and tire position on vehicles with 3-6" lifts. On higher lifts Alpine Long Arm Brackets reposition frame-end control arm mounting points to restore near factory orientation to reduce bushing stress during extreme droop as well as shock load transferred through the Alpine Long Control Arms. The HD Forged Adjustable Front and Rear (4"+) Track Bars and Rear Track Bar Bracket improve steering response center the axles to optimize vehicle roll center and reduce body roll to for unsurpassed handling. This results in improved suspension geometry and relaxed control arm angles for a superior ride quality and performance regardless of terrain. These systems restore front and rear roll axis angles to minimize brake dive and acceleration squat. TeraFlex suspension systems provide reduced noise vibration and harshness (NVH). Alpine CT Suspension Systems are engineered for hardcore Jeeping without sacrificing weekday ride comfort! We recommend Falcon Performance Shocks. Falcon shock absorbers and TeraFlex lift coil springs have been engineered together to improve both compression and rebound for optimal vehicle stability. Alpine CT Suspension Systems are offered with Falcon Series 3.3 Fast Adjust Piggyback Shocks or without shock absorbers. Other Falcon shocks are available separately.

Local Pickup or Install Only - Contact us for Availability 

The TeraFlex JK 2dr: 4" Suspension System w/ 8 Alpine Short Control Arms delivers the necessary components to lift your 2-door JK Wrangler to conquer the most extreme trails and conditions. Features a complete set of adjustable Alpine Short Control Arms HD Forged Adjustable Front Track Bar and rear track bar bracket to optimize suspension geometry. An adjustable rear track bar is recommended. Every TeraFlex suspension system is engineered with drivability and performance in mind. Properly developed suspension geometry roll center and load tuning ensures that all factory stability controls remain functional and within the parameters that Jeep originally engineered into the vehicle. Not only do TeraFlex kits drive straight but they will crawl over anything to get you there and back! Does NOT include shocks. We recommend Falcon Performance Shocks or TeraFlex 9550 VSS Shocks. These are the only shock absorbers engineered to work with TeraFlex lift coil springs to improve both compression and rebound for optimal vehicle stability. Suspension Systems w/ 8 Alpine Short Control Arms are offered with TeraFlex 9550 VSS Twin-Tube Shocks or without shock absorbers. 

Local Pickup or Install Only - Contact us for Availability 

TeraFlex Alpine CT (Cross-Trail) Suspension Systems build on our Sport ST (Street & Trail) Suspension Systems. The TeraFlex 3" Alpine CT3 Outback Overland Short Arm Suspension System is built to handle expedition-style overland travel such as the Canning Stock Route in Australia the Silk Road in China or your favorite trail in the U.S. The Alpine CT3 Outback Overland builds on the standard 3" Alpine CT3 by adding custom load-enhanced heavy-duty rate coil springs. These upgraded springs maintain the lift height when loaded with heavy gear. The Outback Overland Suspension System is built to handle the toughest trails! Our adjustable Alpine Short Control Arms balance front caster angle and pinion angles as well as optimize rear pinion angles anti-squat geometry and tire position on vehicles with 2-4" lifts. The HD Forged Adjustable Front and Rear (4"+) Track Bars and Rear Track Bar Bracket improve steering response center the axles to optimize vehicle roll center and reduce body roll for unsurpassed handling. This results in improved suspension geometry and relaxed control arm angles for a superior ride quality and performance regardless of terrain. These systems restore front and rear roll axis angles to minimize brake dive and acceleration squat. TeraFlex suspension systems provide reduced noise vibration and harshness (NVH). Alpine CT Suspension Systems are engineered for hardcore Jeeping without sacrificing weekday ride comfort! Does NOT include shocks. We recommend Falcon Performance Shocks. Falcon shock absorbers and TeraFlex lift coil springs have been engineered together to improve both compression and rebound for optimal vehicle stability. Alpine CT3 Outback Overland Suspension Systems are offered without shock absorbers. 

Alpine CT3 Outback Overland:

• Lift Height: 3"

• Max Tire Diameter: 35"

• Designed for the additional cargo demands of overland driving

• Load-enhanced heavy-duty rate coil springs CT Short Arm Suspension Systems:

• Adjustable Alpine Short Control Arms balance front caster angle and pinion angles as well as optimize rear pinion angle and tune anti-squat geometry for proper suspension alignment on 2-4" lift kits

• Alpine Short Control Arms are constructed from durable 42mm x 4mm wall DOM tube for maximum strength

• Bolts to the factory control arm mounting brackets

• Install and drive simple bolt-on installation – no welding required Cross-Trail:

• Delivers true Cross-Trail (CT) performance

• Dependable performance w/ zero worries

• Positive, responsive handling w/ reduced NVH

• High-quality, dependable, maintenance-free, factory-style bushings provide excellent NVH damping and ride quality.

• HD Forged Adjustable Front and Rear (4"+) Track Bars and Rear Track Bar Bracket improve steering response, center axles to optimize vehicle roll center, and reduce body roll for unsurpassed handling

• Front SpeedBump and rear Progressive Bump Stops provide progressive compression during high-speed suspension movement

• Coil spring retainers prevent the springs from unseating during full suspension travel

• Full range of movement for off-road flex and articulation

• TeraFlex Limited Lifetime Warranty against defects

Local Pickup or Install Only - Contact us for Availability 

TeraFlex Alpine CT (Cross-Trail) Suspension Systems build on our Sport ST (Street & Trail) Suspension Systems. The TeraFlex 4" Alpine CT4 Long Arm Suspension System is developed for the off-roader craving trails and rocks as well as highway control in a no-compromise package. The Alpine CT4 features our adjustable Alpine Long Control Arms & Brackets as well as HD Adjustable Front and Rear Track Bars for full suspension adjustability no matter the terrain! Our adjustable Alpine Long Control Arms balance front caster angle and pinion angles as well as optimize rear pinion angles anti-squat geometry and tire position on vehicles with 3-6" lifts. On higher lifts Alpine Long Arm Brackets reposition frame-end control arm mounting points to restore near factory orientation to reduce bushing stress during extreme droop as well as shock load transferred through the Alpine Long Control Arms. The HD Forged Adjustable Front and Rear (4"+) Track Bars and Rear Track Bar Bracket improve steering response center the axles to optimize vehicle roll center and reduce body roll to for unsurpassed handling. This results in improved suspension geometry and relaxed control arm angles for a superior ride quality and performance regardless of terrain. These systems restore front and rear roll axis angles to minimize brake dive and acceleration squat. TeraFlex suspension systems provide reduced noise vibration and harshness (NVH). Alpine CT Suspension Systems are engineered for hardcore Jeeping without sacrificing weekday ride comfort! We recommend Falcon Performance Shocks. Falcon shock absorbers and TeraFlex lift coil springs have been engineered together to improve both compression and rebound for optimal vehicle stability. Alpine CT Suspension Systems are offered with Falcon Series 3.3 Fast Adjust Piggyback Shocks or without shock absorbers. Other Falcon shocks are available separately.

Local Pickup or Install Only - Contact us for Availability 

The TeraFlex JK 4dr: 4" Suspension System w/ 8 Alpine Short Control Arms delivers the necessary components to lift your 4-door JK Wrangler Unlimited to conquer the most extreme trails and conditions. Features a complete set of adjustable Alpine Short Control Arms HD Forged Adjustable Front Track Bar and rear track bar bracket to optimize geometry. An adjustable rear track bar is recommended. Every TeraFlex suspension system is engineered with drivability and performance in mind. Properly developed suspension geometry roll center and load tuning ensures that all factory stability controls remain functional and within the parameters that Jeep originally engineered into the vehicle. Not only do TeraFlex kits drive straight but they will crawl over anything to get you there and back! Does NOT include shocks. We recommend Falcon Performance Shocks or TeraFlex 9550 VSS Shocks. These are the only shock absorbers engineered to work with TeraFlex lift coil springs to improve both compression and rebound for optimal vehicle stability. Suspension Systems w/ 8 Alpine Short Control Arms are offered with TeraFlex 9550 VSS Twin-Tube Shocks or without shock absorbers.

Local Pickup or Install Only - Contact us for Availability 

The front axle experiences tremendous amounts of lateral force while turning and those effects increase exponentially during off-road driving. The TeraFlex JK: Front HD Adjustable Track Bars withstand these abusive side loads to dramatically improve steering response and handling. Track Bars also allow lateral adjustment of the axle for proper axle alignment as well as cycling through full suspension travel without interfering with other components. Our Front HD Adjustable Track Bar is recommended for 2.5-6" lifts. Bolts into factory locations – no cutting or welding required. This is the same Front Track Bar used in our 2.5-6" Suspension Systems (Alpine RT Alpine CT Sport ST and w/ 8 Alpine Short Control Arms). A must for anyone who takes their rig off road!

• HD Forged Adjustable Track Bars are 230% stiffer than factory track bars – making them the strongest track bars on the market!
• Bolts into factory locations – no cutting or welding required
•  Front Track Bar works w/ the raised front track bar bracket on our Tera HD Front Axles as well as the Front Track Bar Frame Drop Bracket (# 1953000) 
• High-quality, maintenance-free factory-style bushings w/ an additional rate plate for superior handling and responsive control

Local Pickup or Install Only - Contact us for Availability 

The rear axle experiences tremendous amounts of lateral force while driving and those effects increase exponentially during off-road driving. The TeraFlex JK: Rear HD Forged Adjustable Track Bar withstands these abusive side loads to dramatically improve handling. Track Bars also allow lateral adjustment of the axle for proper axle alignment as well as cycling through full suspension travel without interfering with other components. Our rear track bar also maximizes rear right spring clearance. Our Rear HD Forged Adjustable Track Bar is recommended for 4-6" lifts. Bolts into factory locations or one of our Rear Track Bar Brackets – no cutting or welding required. This is the same Rear Track Bar used in our 4-6" Alpine RT and Alpine CT Long Arm Suspension Systems. A must for anyone who takes their rig off road!

HD Forged Adjustable Track Bars are 230% stiffer than factory track bars – making them the strongest track bars on the market!

• Bolts into factory locations – no cutting or welding required

• Rear Track Bar works w/ our Rear Track Bar Brackets (2.5" Lift: 1954776 or 3-6" Lift: 1954777 or 2.5" Spacer Lift: # 1954202)

• High-quality, maintenance-free factory-style bushings w/ an additional rate plate for superior handling and responsive control

Local Pickup or Install Only - Contact us for Availability 

The TeraFlex JK: HD Forged Drag Link Kit & HD Chromoly Tie Rod Kit withstands extreme conditions and abuse that typically causes factory steering components to bend and fail on lifted JK Wrangler/Unlimited models.

HD Forged Drag Link Kit – (# 1853920)

• Bolts directly to new High Steer Knuckle (not included)

• 50% stiffer than factory drag link to help eliminate front end shimmy and other alignment issues

• 1.25" O.D. fully forged drag link eliminates excess movement during hard steering maneuvers

• Utilizes oversized DOM factory-style adjusting collar and pinch clamp for simple adjustments

• Tie rod joint incorporates same features found in TeraFlex Ball Joints, including 4140 chromoly ball/stud and 1045 carbon steel housing

• Adjustable joint preload tension to ensures proper long-term durability

• Joint is pressed into rod end housing and secured w/ snap ring

• Provides clearance for factory 17" wheels HD Chromoly Tie Rod Kit (# 1853910)

• HD 1-5/8" O.D. 4140 heat treated chromoly steel

• More than 200% stronger than factory tie rod

• Forged tie rod housing designed specifically for JK Wrangler/Unlimited

• Tie rod end joint incorporates same features found in TeraFlex ball joints, including 4140 chromoly ball/stud and 1045 carbon steel housing

• Features adjustable rod end preload tension to ensure long-term durability

• The joint is pressed into the rod end housing and secured w/ a snap ring

• Tie rod end joint rotation is limited to 14 degrees of movement to minimize tie rod roll

• Provides clearance for factory 17" wheels

• Steering Stabilizer Relocation Mount Bracket Kit – HD Tie Rod (# 1123160) Steering Stabilizer Relocation Mount Bracket Kit – HD Tie Rod (# 1123160)

• Fits heavy-duty 1-5/8" tie rod

• 6061-T6 aluminum clamp and forged 10.9 grade stud

• Moves steering stabilizer up nearly 2.5" to help reduce damage to the stabilizer shaft or body

• Repositions stabilizer to reduce tie rod roll" associated w/ stabilizer misalignment